- UWAL Info
Flow visualization can be used to show how the air moves over and around the model. The methods below are readily available. Other methods can be accommodated – please contact UWAL. A summary of flow visualization methods is included in the table below:
Table 1: Flow Visualization comparison
|Method||Flow Vis. On Model||Flow Vis. Off Model||Photos w/ Wind-on||Photos w/ Wind-Off||Effect on Data|
*Ultraviolet light available for enhanced visibility
Using a custom-made smoke generator and probe, a stream of white smoke can be inserted anywhere in the test section by positioning the probe using the traverse rig or by hand.
Advantages : Easy setup and quick repositioning of the probe allows for viewing flow patterns around any portion of the model.
Disadvantages : Extended use fills the tunnel with smoke. The tunnel must be vented to remove the smoke before further flow visualization can be used. An oily residue is left on whatever the smoke touches. Furthermore, pressure taps must be protected to prevent clogging.
Smoke flow visualization over a wing
There are three types of tuft flow visualization techniques readily available at UWAL.
Fluorescent Minitufts : Small filaments of polyester monofilament thread soaked in a UV dye are glued to the model surface. When the wind is turned on, the minitufts move in the direction of the flow. A UV flash is used to cause the minitufts to fluoresce, making them appear larger for better visibility. Digital still-photos are the only means for capturing the minituft orientation.
Thread Tufts : Pieces of number 60 sewing thread are taped or glued to the model surface. When the wind is turned on the tufts move in the direction of the flow. The sewing thread can be further enhanced with UV lighting.
Tuft Probe : A probe with a single yarn tuft can be positioned anywhere in the test section with the use of the traverse rig.
Advantages : Allows flow visualization at any model position. Yarn tufts are easy to install. A tuft grid provides a view of the flow pattern over a large area. Minitufts have a negligible effect on force data. Sewing thread makes a good tuft due to its clear visibility in UV or normal light, it has smaller flow effects compared with yarn, and its ease of application compared to minitufts.
Disadvantages : Does not provide a detailed flow pattern since they are constantly moving with the air flow. Minitufts require more time to install but can be left on the model.
Flourescent minitufts on aircraft wing
A mixture of kerosene, clay powder, and DayGlo™ pigment is applied to the model surface with the wind off. When the wind is turned on it causes the kerosene to evaporate, leaving streaks of clay powder in the form of the flow pattern.
Advantages : Easiest method to setup and apply. Provides lasting flow pattern on the model for photos when the wind is off. Clearly shows flow pattern; shows flow separation well.
Disadvantages : Cannot vary model position during flow visualization. Model must be a dark color, preferably flat black, for contrasting the powder against the model surface. Pressure taps must be protected to prevent clogging.
China Clay Flow Visualization
A mixture of oil or oil substitute and dye can be applied to the model surface. When the wind is turned on, the oil and dye particles slowly move in the direction of the local flow. For improved visibility of the oil flow, an ultraviolet dye can be used such that when illuminated with an ultraviolet light the dye fluoresces to clearly show the flow pattern.
Advantages : Provides somewhat lasting air flow pattern on the model for photos when the wind is off. Gravity will slowly change the oil pattern. Clearly shows flow pattern, especially the transition between turbulent and laminar flow as well as separation. UV oil is the most photogenic of the flow visualization methods.
Disadvantages : After time, all of the oil will run off the model. Model must be a dark color, preferably flat black, for contrasting the oil mixture against the model surface. Pressure taps must be protected to prevent clogging.
UV Oil On Wing Showing Transition Point
A mixture of naphthalene and trichloroethane is applied to the model surface with the wind off. When the wind is turned on, it causes the chemicals to sublimate. Turbulent areas cause the chemicals to sublimate faster than laminar areas.
Advantages : Shows areas of turbulent and laminar flow.
Disadvantages : Cannot vary model position during flow visualization. Model must be a dark color (preferably flat black) for contrasting the white chemicals against the model surface. Pressure taps must be protected to prevent clogging. Flow pattern disappears with time. Chemicals must be chosen properly for the tunnel speed and temperature to obtain a good sublimation rate.
Sublimating Chemicals Showing Transition Point On a Wing